Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - DaPiV90

Pages: [1]
PDW Support / Re: PDW on Surface 3 - stops when screen blanks
« on: 06 Dec 2016, 09:44:26 »
Hi Michael

my first thaught is that the input shuts down with the screen...
Maybe you shold test that before going further?


PDW Support / Re: Show more than one Label?
« on: 06 Dec 2016, 09:09:55 »
I don't want to make it a lot more complicated. I just thaught it was possible to make a database for the adresses.
PDW works fine for me so i don't want make the chain longer :)

Thank you for the answers, cheers Dave

PDW Support / Re: Show more than one Label?
« on: 05 Dec 2016, 11:58:06 »
So my situation shown on an example.

I have currently about 220 filrters
every Adress given with a filter lable with its alias
Adress: 1234567 Lable Car#1 (Adress based)
Adress: 1234568 Lable Car#2 (Adress based)
Now i want to have a secound lable for a specific lokation
Adress: 1234567 Lable Car#1 (Adress based)
Adress: any(7x?) Lable City#1 (Text based)

When i make a filter for City#1 (like above) only this filter is shown.
So i don't know if Car#1 or Car#2 is in City#1....

Is there another possibilytiy to make the aliases without using the filter? Something like a data base with adress and alias?

PDW Support / Show more than one Label?
« on: 04 Dec 2016, 12:27:35 »

i was woundering if it is anyhow possible to make the filer monitor show more then one Label?
I have sometimes messages thet trigger two filter with a seperate Label and pdw is only showing one fo them.

Cheers Dave

Scanners and receivers / Pager Antenna improvement...but how?
« on: 19 May 2015, 19:35:39 »
Hello @ all,

i just got my Pager with the discriminator output back from the Netherlands. Now i have the problem, that the pager signal sent to my computer is very poor so i think it is an problem with the internal antenna.

So my question to you guys is how can i improve the antenna of my pager? I just removed the original build in antenna and connected two cables to the points on the board. Now i have the disc. output and two cables for the antenna on the outside of the pager...but no idea what to do next...:/


PDW Support / Re: Soundcard configuration
« on: 28 Apr 2015, 22:54:40 »
Hi again,

[bad english]

so i tried almost everything and the problem was, where i never thought to find it... my antenna  :P

So i ordered a new one (the parts for it) and now... 100% reading in pocsag1200 mode.. I love PDW  :-*

[/bad english]


PDW Support / Soundcard configuration
« on: 18 Apr 2015, 13:16:19 »
Hi @ all,

i was running PDW on my old system with no problems at all. Sometimes i had to restart but that is no problem for me so i was very happy with the overall work of PDW.

Now i changed almast all components of my system like Mainboard, CPU and i am running into the problem that PDW stops decoding. I have to change the Interface configuration to another source. For example from Discriminator 1 to Discriminator 3 and than PDW starts to work again. This problem shows up about all 4-5 hours.

Someone got an idea what is going on there? I changed the Input volume of my system (the sweet spot seems to be about 85-87) but that doesn't have any effect...

Hope for help
Greetings Dave

sorry for my bad English :)

PDW Support / [found it, sorry]Filter Monitor size
« on: 09 Apr 2015, 08:30:25 »
Hi @ all,

i am using the pdw software with my UBC69XLT-2D an everything works great. Thank you for the very good work.

One question: Is it possible to change the size of the Filter Windows in the lower third of the screen?

Just found older post. Thanks a lot :)


Pages: [1]